Chassis | drawbar

Cenius_5003-2TX_Super_003_d1_141223_kl_rdax_170x121.jpg

Fast on the road

The smaller trailed Cenius 4003-2TX and 5003-2TX are equipped as standard with the 400/60-22.5 tyres, whereas, on the wider 6003-2TX to 8003-2TX, the oversized 550/45-22.5 tyres are fitted as standard. As an option, these are also available for the Cenius 4003-2TX and Cenius 5003-2TX. For the wider models, 700/40-22.5 tyres are available as well. When equipped with air braking, high speed transport of up to 40 km/h is permitted.


“In transport the Cenius TX safely travels on its over-dimensioned running gear.”
(traction – working test AMAZONE Cenius 5003-2TX Super · 3/2016)

More information + Less information -

High output

Working widths of up to 8 m in combination with the optional traction assistance provide a high work rate. Thanks to its centre running gear, the Cenius-2TX is especially manoeuvrable on the road and in the field.

More information + Less information -

Integrated running gear in a class of its own

"Performance in work: the soil is well mixed, very well levelled and the edges are clean."

"The roller has a very good carrying ability and matches our soil types 100 percent. During the total time we used it, it did not clog even once.”


(traction – working test AMAZONE Cenius 5003-2TX Super · 03/2016)

More information + Less information -
Cenius_7003-2TX_Detail_005_d1_140611_kl_rdax_170x121.jpg

Centralised and simple depth adjustment

At the front of the machine, support wheels carry out the depth guidance. At the rear of the machine the depth rollers take over this task.

Zentrale und einfache Tiefenverstellung (1) Tiefeneinstellung_1

If it is intended to adjust the working depth whilst on-the-move to react to varying soil conditions or to repair harmful compaction, the optionally available step-less hydraulic depth control is recommended. The depth setting of the support wheels, of the running gear and of the depth roller are synchronised through a hydraulic system via a double acting control valve – a big gain in comfort for the Cenius-2TX!

Zentrale und einfache Tiefenverstellung (2) Tiefeneinstellung_2

When working with depth rollers, the required lift height of the running gear is accurately defined for a minimum turnaround time on the headland. If, during operation, the working depth is adjusted, the lift height of the wheels is automatically matched via the hydraulic system. In this way any “running along” of the wheels is prevented. If, however, on areas with very light soils where some additional help from the transport wheels is desired, this can also be set.

Zentrale und einfache Tiefenverstellung (3) Tiefeneinstellung_3

In very wet conditions, in late autumn or when leaving the field to overwinter, the Cenius-2TX can be operated without a depth roller. In this special case, the chassis serves as the depth control. Comfortable to use spacers can be swivelled around the piston rod of the running gear hydraulic cylinder to keep the running gear then at the desired working depth. The tines at the rear of the wheels serve as wheel mark eradicators to ensure a level finish.


  • “The support wheels in front and the following roller at the rear reliably maintain the pre-set working depth.” (dlz agrar magazine · 02/2015)
  • “Comfortable and practical is the hydraulic depth adjustment of the tines which Amazone offers as an option.” (profi Practice test “Trailed cultivators Part 2” · 06/2017)







More information + Less information -
Cenius_11-2015-20.jpg

Traction assistance for Cenius-2TX

  • Increase in tractor traction
    - Weight transfer from the Cenius on to the tractor’s rear axle
    - up to 1,500 kg additional weight on the rear axle
  • Reduction in wheel slip
  • Increase in acreage output
  • Reduction of fuel consumption
More information + Less information -
Cenius_5003-2TX_Deichsel_001_d0_20150424_d1_1509281_kl_rdax_170x117.jpg

Linkage for Cenius-2TX and Ceus-2TX

The flanged linkage means the maximum flexibility of choice. So, for any tractor the suitable linkage system can be selected; no matter whether a lower link cross shaft in Cat. III, IV, V, different pulling eyes or the K80 ball coupling.

More information + Less information -

Related links

Here you will find further information on cultivation

Are you interested?

Provide us your contact details* and we will get back to you:
* Your contact details will only be used to contact you as requested.